Service Added. Need to Add Another?
Add another service to your design from the tools below. Select a section on the left, then add the service. You can duplicate services between sections by cutting and pasting, or recycle scraps you don't need.
|Mill||Mohawk Fine Papers|
|Size||25 x 38|
|Printer Compatibility||Offset Printing|
|Grain Direction||Grain Long|
Elemental Chlorine Free FSC Certified Lignin Free Made Using Wind Power
100 lb Text 148 G/M2 Caliper 7.8 256 PPI
|Paperator™ Color Value||
CMYK C = 0, M = 3, Y = 0, K = 0
RGB R = 255, G = 248, B = 254
Mohawk Superfine Papers are easy to print on when following these simple hints. It is recommended to pre-test all printing procedures prior to press time to ensure the desired results are achieved.
Print Mohawk Superfine like any conventional uncoated paper. We recommend heat resistant, wax free ink if you plan to follow lithography with xerographic or laser printing technologies.
Keep Mohawk Superfine products wrapped until the moment of printing. It is essential to let the paper acclimate, for a minimum of 24 hours – longer during cold weather – in the press room while still wrapped in mill packaging. Keep Mohawk Superfine products covered during drying, between passes and prior to any finishing work. Pressroom conditions should be as close as possible to 70 degrees, and 40-50% relative humidity.
Dull varnish or dull aqueous is optional as a surface protector.
For best results, 100lb. text papers and all cover weights should be scored before folded. Folds against the grain, gatefolds, and folds running throughout heavily inked areas should also be scored. As a general rule of thumb, the correct creasing channel is determined by multiplying the paper’s caliper by two and then add the width of the creasing rule. (Note each 1 pt. of rule equals .014 inch). Mohawk recommends a minimum 2 pt. rule for all scores both with and against the grain. Sometimes a wider score must be added – but too much width can be worse than too little, causing the sheet to fold unevenly on one side of the score rather than the center. A double, parallel score can be used to keep it straight.
Mohawk Superfine is suitable for all standard binding processes. It is important to plan for proper grain direction in all binding applications. Grain direction should run parallel to the spine for optimum results.
Laser guaranteed on all basis weights within the limits of your equipment. The laser guarantee is extended to include paper after preprinting offset if the preprinting guidelines included herein are followed.
Most Mohawk papers are engineered for high-performance on both offset and digital printing equipment. Many applications, such as forms and letterheads, require you to have folio-size sheets preprinted with offset lithography and trimmed down for subsequent printing in digital equipment. We guarantee our folio papers for these applications, provided standard industry guidelines for preprinting are followed. Please note that heat-set web offset printing is not recommended for pre-printed shells.
Papers with good formation (an even distribution of fibers) and a smooth finish provide the best results in most digital equipment. Bright white paper will add to color brilliance, contrast and definition. Toner does not adhere well to uneven paper surfaces, so heavily textured or embossed papers are not recommended for traditional digital presses. Check the specifications of the digital printing equipment before running coated paper.
The paper’s basis weight should fit within the equipment’s specifications. Some machines must run 20 to 24 lb. (70 to 90 gsm) paper; others have a much wider range. Plain paper samples for testing in digital printers are available.
Paper merchants can provide samples of the specific paper grade, basis weight and size.
Although newer digital color production presses can run a wide range of substrates, HP Indigo presses have particular substrate limitations that have traditionally been solved by using sapphire-treated papers. Mohawk’s i-Tone® process was developed to overcome these issues, improving both toner adhesion and blanket memory. It enhances print quality on the HP Indigo, the Kodak NexPress, and the Xerox iGen3™ Digital Production Press.
Unlike Sapphire-treated papers, Mohawk i-Tone papers can be offset printed and then run through an HP Indigo press. Please consult your HP Indigo printer for specifications for the offset print run.
Stationery and forms preprinted with ordinary ink will smear under the extreme heat and pressure of fuser rollers in high-speed copiers. In addition, improper handling and storage may cause jams. It is important to follow these standard industry practices when printing jobs that will be run through copiers and laser printers.
Provide the copy/laser printing schedule to the offset printer, so that the job is planned correctly. Discuss options if it is a tight turnaround.
The ink manufacturer can provide inks for laser applications. The job will require oil-based heat- or thermal resistant inks. Inks should withstand 400° Fahrenheit without smearing. Avoid metallic inks as the metallic flakes can build up on the fuser rollers. Fluorescent inks are also not recommended. Minimizing ink and water on press should help reduce the possibility of wavy paper.
Anti-offset powder or spray residuals can interfere with toner application and build up in the system, causing problems.
Toner does not adhere well to heavily printed areas. The digital image should print directly onto the paper, avoiding an overlap of offset ink. If the job specifies an overprint of a preprinted solid area, use a halftone screen to achieve the desired color.
If planning to imprint just one side of the preprinted form, print and pack so that the top (felt) side is imaged. For twosided copying, the bottom (wire) side should be imaged first. Note: Mohawk papers are packed felt side up in cartons and reams. Care should be given when specifying relief processes, such as thermography, engraving, foil stamping, and embossing as they may damage your equipment and cause jams.
Paper must be trimmed precisely, square, and with clean cuts. Improperly trimmed paper can misfeed and cause performance problems.
Prevent tight plastic shrink-wrapping as it will curl edges and corners, leading to jams. Packing with chipboard is preferable. After wrapping, store preprinted material for 10 days before using to ensure completely cured ink and acclimated paper. Store at 50% relative humidity, at 70° Fahrenheit.
A wide variety of papers available for use in HP Indigo presses are sapphire treated to yield consistent image quality and maximum ElectroInk adhesion. Papers that have been sapphire treated are sensitive to environmental conditions. Heat and humidity play a key role in maintaining the shelf life of such papers. Product shelf life is approximately 6 months from the treatment date when store at 70 degrees F (21 degrees C) and 50% relative humidity. We recommend keeping sapphire treated papers in the original shrinkwrapped packages until ready to print. Any unused paper should be rewrapped for protection and to ensure optimum performance on press.
Testing the runnability of envelopes is recommended. Because of multiple paper thickness and variable envelope construction, we cannot guarantee performance once papers are converted into envelopes.
Paper merchants can provide specific envelope samples for testing.
Due to the large variety of equipment available for both offset and digital printing, we strongly recommend testing any paper before committing to a large program.
For more information and samples, please call Mohawk at 1 800 THEMILL. www.mohawkpaper.com.
Desktop Laserjet Printing, Laser Printing and Inkjet Printing, thermography, flexographic printing, letterpress printing, gravure printing, screen printing, foil stamping, engraving, embossing, die cutting, saddle stitching, perfect binding. A Superfine i-Tone version is available for HP Indigo presses.
Confirm Services to Complete this Order
Your paper will be cut with state-of-the-art paper trimming equipment operated by paper industry professionals who understand the details of your design. Specify any size. Our online cutting designs are exact. Cutting usually takes 2 - 3 days, but let us know if you have a tighter schedule.
Whether you need return receipts, business cards or shelf-talkers, our online design is easy. Choose from 46 standard formats or order your custom dimensions on perpendicular edge-to-edge perforations. Perforating usually takes 3 - 4 days, but let us know if you have a tighter schedule.
Paper hole punching provides clean, crisp, circular holes for a variety of binding applications. Have us custom hole punch almost any paper available on The Paper Mill Store. Hole punching usually takes 2 - 3 days, but let us know if you have a tighter schedule.
Proper folding, without cracking, usually requires a nice crisp score to create a hinge for the paper to fold along. Have us custom score almost any paper available on the site. Scoring usually takes 2 - 3 days, but let us know if you have a tighter schedule.
This will erase ALL added services from your current product.
How do you use paper?